Skip to main content

Peacock Necklace Tutorial


I can't open a magazine or visit a fashion website without seeing some kind of feather accessory. Yes, I do make feather hair clips but I thought it would be fun to try my hand at making some jewelry. So after a little craft exploration I came up with an idea for a necklace out of feathers and an old plain chain necklace.

Supplies:
5 peacock eye feathers
Scissors
Paper
Pencil
Glue Gun
Stiff Felt (the kind you buy by the square)
Needle
Thread that matches felt
Old chain necklace (if you don’t have an old chain necklace you can purchase new chain and findings in most craft stores)

  1. Take three of your peacock feathers and trim the wispy eyelash like ends off of the rounded top and cut off the stem just below the “eye” (see fig. 1).

  2. Arrange the feathers similar to fig. 2a on top of the piece of paper. Carefully trace around the feathers. When you remove the feathers place them to the side in the exact order you had them on your paper pattern.


  3. Take the pencil and draw a line inside the current outline that follows the shape of the original outline. Your new “inside” pattern should be about an eighth of an inch (give or take) from the original “outside” line. Cut out the “inside” pattern shape.

  4. Use the cut out paper pattern to cut out the felt backing. Place feathers on top of the felt to make sure that you can’t see any of the felt when the feathers are in position. Trim the felt if necessary.

  5. Take the chain and place the middle center aligned with the top center of the felt (see fig.5a). Sew the chain in place. Next take the chain and move one side to the left top corner and sew in place, repeat with right side (fig. 5b).


  6. With your trimmed feathers close by, take the glue gun and put a thin layer on the left side.* When the area is covered pick up the left hand side feather and carefully place it on the glued area. If the placement is not perfect DO NOT WORRY, that is why we have the other two feathers that we haven’t touched yet sitting on the side.

    *NOTE: It is very important that the glue does not have any thick beads, to help avoid this make sure your glue gun is very hot and take the tip and place it right up against the felt and move it around the area.

  7. Repeat step 6 with the right and center feathers.

    NOTE: Because hot glue is unforgiving and you can’t move the feathers around after they have touched the glue, you might notice small gaps where you can see the felt. Do not worry the next steps will cover these little gaps.


  8. Trim the two remaining feathers similar to the others, except you will be cropping closer to the eye, see fig. 8 for a reference.


  9. On the back side of the trimmed feathers, put a bead of glue along the stem (fig. 9a) then place the cropped feathers over the felt to cover the gaps (fig. 9b)



Comments

  1. How unique and creative ! I'm thinking it can make a beautiful altered evening bag too. Thanks for the inspiration

    ReplyDelete
  2. Hi,

    The peacock necklace is so nice, this exotic strand of natural-color Tahitian pearls features a multicolor array of silver pearls with various pink and cherry hues, as well as several dark peacock pearls. Thanks...

    Peacock Necklace

    ReplyDelete
  3. I like it very much!!
    The problem is finding these bautiful feathers! :)
    Cecilia

    ReplyDelete
  4. very smart :)
    thanks for instructions!!!

    ReplyDelete
  5. This is a great tutorial, thanks for sharing! (found you via Totally Tutorials)

    ReplyDelete
  6. Love this!! So Cute I'm going to try this soon!

    ReplyDelete
  7. Love this beautiful necklace... Very unique and very creative! Thanks for posting.

    http://glasspoppies.etsy.com
    http://glasspoppies.blogspot.com

    ReplyDelete
  8. Ooooo I love it!!! Fantastic, I like I will try it but with polymer clay!!! I love you Etsy shop too!!

    ReplyDelete
  9. oops, I meant I THINK I will try it....

    ReplyDelete

Post a Comment

Popular posts from this blog

Leather Earring Tutorial

Why should leather only be used for jackets, shoes and purses? Medium weight or upholstery leather is easy to craft since it doesn't fray or crinkle. These leather earrings are quick, versatile and easy to make. You can even recycle those old purses or jackets that have damage since you really only need small amounts of good leather. I used 4" square leather samples and had plenty left over to make more earrings. Supplies: Leather Leather punch (I bought mine at Michaels Craft store for around $10 but you can also get the from home stores like Home Depot or Lowes) Sharp scissors 2-Large Jump Rings 2-Earring wires Jewelry pliers Download the pattern below, print and cut out shapes. Cut 2-of each shape in the leather of your choice. I used 3 different types of leather, don't be afraid to mix it up. Pile one set of the three shapes on top of each other and carefully punch a whole on one of the ends. I punched the hole about a quarter of an inch away from the end using the sma

Leather Earring Pattern Update

In October I posted a tutorial to make leather earrings . Well for Christmas I revisited this craft and made a few other designs for a few people at my work. This is one of my favorite tutorials because they are so easy to make and the earrings are light and easy to wear. I liked the new designs so much I thought I would share the pattern for them. To view the full set of instructions on how to make these leather earrings, click here . To make one of the two pairs shown, download and print the updated pattern below (the bottom row are the new designs):

Washer Necklace Tutorial

Every time I buy furniture that requires assembly I always left over hardware. I take this hardware and put it in a jar thinking that one day I will need that extra nut or bolt. Well today is that day! Below is a tutorial on how to take those extra washers and make them into a cute necklace. Supplies: Scissors X-acto knife or hole punch Pencil Small piece of scrapbooking paper (you can use the left over scraps for this project) Modge Podge (or something similar) Washer Aleene’s Paper Glaze 36” of ribbon or cord Use the washer to trace a circle on the paper, don’t forget to trace the inside circle as well. Using your scissors cut just inside of the traced line on the outer circle. Note: you want to cut inside of the line and not on it so it fits on the washer and does not overlap the edges. If the hole for your center is close to the same size of a hole punch, simply punch out the center circle. If not use the X-acto knife to cut out the center area. Modge Podge the paper to the washer